Ricambi Lascal BuggyBoard: cosa serve e quando

Quick answer

Buy spare parts only for the fault you can actually see: a dragging or noisy wheel usually means the friction pads, a board that rattles or sits loose usually means the extender bolts, and a board that no longer reaches your pushchair legs usually means arm extenders. Start with the cheapest correct part, fit it, then retest the board before buying anything else. If the board itself is cracked or the wheel axle is bent, replacement parts will not save it.

Match the symptom to the part before you order

Most BuggyBoard problems look like one fault but come from one of four small parts. Work through them in order of cost and effort rather than ordering everything at once.

Noise, drag or a wheel that skips: the friction pads are worn. Loose, wobbly or rattling connection: the extender bolts need tightening or replacing. Board sitting too far from the pushchair legs: arm extenders. Connectors slipping on the leg or axle: connector bolts. If none of those fit, check the wheel and axle themselves, because a bent axle is not a spare-part fix.

• Grinding or squealing wheel: friction pads first.
• Rattle or movement at the joint: extender bolts.
• Board will not reach the pushchair: arm extenders.
• Connectors creep or slip: connector bolts.
• Cracked board or bent axle: replace the board, not the part.

What each spare actually does

Friction pads sit against the wheel and control how the board rolls. Once they flatten, the wheel drags, the board feels heavy and the noise gets worse. A replacement set restores smooth, quiet movement and needs no extra tools, so it is the lowest-risk first purchase.

Arm extenders add reach, not strength. They extend the arms up to 6cm, which is what you need when the board sits too close to the pushchair or the connectors will not line up with the legs. They are sold as a pair and the extender bolts are not included, so if your current bolts are worn, order both.

Extender bolts hold the arm position. The movement of the board can loosen them over time, so they need tightening before every use. That is normal, not a fault. If a bolt no longer holds its setting even after tightening, replace it rather than overtightening.

Connector bolts hold the cotter pin that attaches the board to the pram and secure the connectors onto the pushchair legs or axle. If the board shifts sideways or the connector will not clamp firmly, these are the parts to check.

How to check wear without tools

Do this on a flat floor with the pushchair stationary. Lift the board and spin the wheel by hand: if it stops quickly or sounds rough, the friction pads are the likely cause. Push the board side to side: movement at the arm joint points to extender bolts. Try to rotate a connector by hand: any slip means the connector bolts need attention.

Then walk a short distance and listen. A rhythmic noise that speeds up with the wheel is almost always the wheel or pads. A single knock on each step is usually a loose joint. This takes two minutes and stops you buying a part you do not need.

Tightening versus replacing

Tighten first, replace second. Extender bolts are designed to be re-tightened before every use, so a loose bolt is not automatically a worn bolt. If it holds for a full trip after tightening, keep it. If it works loose within minutes, replace it.

Friction pads cannot be tightened back into shape, so once they are flat or glazed they are done. Connector bolts are a judgement call: if the connector still clamps firmly after a clean and re-tighten, keep it; if it slips on the leg, replace the pair.

Keeping spares on hand

The parts that fail most often are also the cheapest, so a small spares box saves a mid-trip problem. Friction pads and a spare extender bolt cover the two most common failures. Add a pair of arm extenders only if your pushchair setup is close to the limit of the board's reach.

Store them with the BuggyBoard user manual so part numbers are to hand when you reorder. Lascal part numbers are printed on the packaging and are the fastest way to confirm you have the right item.

• Friction pads: buy two sets if you use the board daily.
• Extender bolt: one spare is enough, sold individually.
• Arm extenders: only if your board is at maximum reach.
• Connector bolts: replace as a pair, not singly.

Decision rules for buying BuggyBoard spares

• Wheel noise or drag: If the wheel spins roughly or the board feels heavy, replace the friction pads before anything else. Cheapest fix, fits all models, no tools needed.
• Loose or rattling joint: Tighten the extender bolt and retest. Replace it only if it works loose again within a single trip. Tightening is part of normal use, not a sign of a faulty part.
• Board will not reach the pushchair: Measure the gap first. Arm extenders add up to 6cm of reach, and the bolts are sold separately. Order extenders and bolts together if your bolts are worn.
• Connectors slip on the leg or axle: Clean and re-tighten the connector bolts. If it still slips, replace the pair. Replace connector bolts as a pair, never singly.
• Cracked board or bent axle: No spare part listed here will fix a damaged board or axle. Replace the board instead of chasing parts.

Spare parts worth knowing

• Lascal BuggyBoard Replacement Friction Pad (2pce): Replacement friction pad set containing two pads, compatible with all Lascal BuggyBoard models, with no additional tools required. It is the cheapest fix for a noisy or dragging wheel and fits every board, so it is the safest first part to try.
• Lascal BuggyBoard® Spare - Pair Of Arm Extenders: Pair of arm extenders, part number 80372, compatible with Lascal Mini and Maxi BuggyBoard, extending the arms up to 6cm; extender bolts are not included. Buy these when the board will not reach the pushchair legs, and budget for bolts too if yours are worn.
• Lascal Buggyboard® Spare - Extender Bolt Grey: Extender bolt, part number 80371, compatible with Lascal Mini and Maxi BuggyBoard, sold individually; it needs tightening before every use because board movement can loosen it. Explains why a loose joint is not always a broken part, and why one spare bolt is a sensible thing to keep.
• Lascal BuggyBoard® Spare - Pair Of Connector Bolts Black: Pair of connector bolts, part number 80000, compatible with Lascal Mini and Maxi BuggyBoard; they hold the cotter pin and secure the connectors onto the pushchair legs or axle. These are the parts to replace when the board shifts sideways or a connector will not clamp firmly.

Who these spares suit

Best for

• Owners of a Lascal Mini or Maxi BuggyBoard with a specific, visible fault
• Families who want to keep a working board going instead of buying a new one
• Anyone who wants a small spares box for daily use

Not for

• Boards with a cracked deck or bent axle, which need replacing rather than repairing
• Buyers who are unsure which BuggyBoard model they own, since compatibility should be confirmed first
• Anyone hoping a single part will fix several unrelated symptoms at once