Start with the pin, not the whole board
If your BuggyBoard feels loose or starts to wobble, the cotter pin is one of the first things to check. It is the small threaded pin that passes through the BuggyBoard Connector and holds the board to your pram. Because the board moves constantly in use, the pin can work loose over time.
The Lascal BuggyBoard Spare Cotter Pin (part number 81520) is the replacement for that connection point. It is a plastic threaded pin approximately 2 inches long and is compatible with both the Lascal Mini and Maxi BuggyBoard. Before you assume the whole connector or board is worn out, inspect the pin and its seating.
Signs the cotter pin needs attention
Use these checks to decide whether the pin itself is the likely cause of movement. They describe what the supplied product information supports, not a full diagnosis of every possible wobble.
- The board moves more than usual at the connector: The cotter pin attaches the board to the pram through the connector. If movement is concentrated at that joint, the pin is a sensible first check.
- The pin has loosened during use: Lascal notes that the movement of the board can often lead to loosening, so the pin needs to be tightened before every use. A pin that no longer stays snug is a candidate for replacement.
- The pin is damaged or hard to remove: Over-tightening can damage the plastic slot on the head of the pin, which causes problems if you ever need to remove it. If that damage has already happened, a spare pin restores a clean connection point.
- You are missing a pin: The pin fits through one of the three holes in the Left and Right Arm, depending on your pram. If a pin has been lost, the board cannot be secured as intended.
What the Lascal spare cotter pin is specified to do
- Lascal BuggyBoard® Spare - Cotter Pin Black: A plastic threaded pin approximately 2 inches long that fits through the Lascal BuggyBoard Connector, attaching the board to the pram. This is the exact connection point to inspect when the board wobbles or the pin is missing.

Lascal BuggyBoard® Spare - Cotter Pin Black - Lascal BuggyBoard® Spare - Cotter Pin Black: Compatible with Lascal Mini and Maxi BuggyBoard. One spare covers both board models, so you can order with confidence if you own either.
- Lascal BuggyBoard® Spare - Cotter Pin Black: Part number 81520. Useful when checking you are ordering the correct small spare rather than a different connector part.
- Lascal BuggyBoard® Spare - Cotter Pin Black: Attaches to 1 of the 3 holes in the Left and Right Arm, depending on pram. Explains why the pin position can differ between prams and why the hole choice matters during fitting.
How to fit the replacement cotter pin
These steps follow the supplied product details. They do not replace your BuggyBoard user manual, which Lascal provides for the full fitting instructions.
- Identify the correct hole: The pin fits through one of the three holes in the Left and Right Arm. Use the hole position that matches your pram and the existing setup.
- Insert the pin through the connector: Pass the threaded pin through the BuggyBoard Connector so it attaches the board to the pram.
- Tighten securely, but do not over-tighten: Lascal advises ensuring the pin is securely in place while being careful not to over-tighten, as this may damage the plastic slot on the head of the pin.
- Re-tighten before every use: The movement of the board can loosen the pin, so check and tighten it before each use as part of your setup routine.
The trade-off: a small spare that needs routine attention
A cotter pin is an inexpensive part, but it is not a fit-and-forget component. The same movement that makes a BuggyBoard useful can loosen the pin, so tightening before every use is part of living with it. That routine is simpler than replacing a whole connector, and keeping a spare means a lost or damaged pin does not sideline the board.
If the pin is secure and the board still wobbles, the supplied information does not identify other causes. In that case, check the BuggyBoard user manual and inspect the connector and arms rather than assuming a new pin will solve everything.


